Featured in Logging Equipment
Photo |
Title
|
Make | Model | Year | Price |
![]() |
Custom Built ChipperCustom Built Chipper. 23" diameter capacity. 380 HP Cummins with low hours on an overhaul. 3 knife. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
- | - | - |
$17,500
|
![]() |
Bandit 1850XP Tracked Chipper1998 Bandit 1850XP Track Chipper. Hour meter reads 4,000 hours, unknown if original. New Cummins 250hp engine and new glass. New master switch. Boom and grapple are tight. Ready for work. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Bandit | 1850XP | 1998 |
$95,000
|
![]() |
Timbco 425 Feller Buncher with Quadco 20B Head1993 Timbco 425 Feller Buncher with Quadco 20B Head. Hour meter reads 6,304 hours, frame hours are unknown. Cummins 8.3 engine starts and runs good. 24" single grouser pads, undercarriage is estimated at 90%. All pins and bushings are tight. Leveling system is in working order. Final drives have been gone through and greased. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Timbco | 425 | 1993 |
$37,500
|
![]() |
Komatsu 220LC with Limmit 2100 Delimber2009 Komatsu 220LC with Limmit 2100 Delimber. Hour meter reads 13,032 hours. New boom at 11,000 hours, and new cables & hoses at 12,800 hours. 32" triple grouser pads, undercarriage is estimated at 80%. Heat, A/C, radio, & lights. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Komatsu | 220LC | 2009 |
$72,500
|
![]() |
John Deere 2154D with Limmit 2100C Delimber2013 John Deere 2154D with Limmit 2100C Delimber. Hour meter reads 9,428 hours. 650 hours on new engine and rebuilt hydraulic pump. Winch cables, hoses, and drive motors were gone through over the winter. 24" double grouser pads, undercarriage is estimated at 90%. 500 hours on new rails, sprockets, & rollers. Heat, A/C, radio, & lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
John Deere | 2154D | 2013 |
$163,500
|
![]() |
Timbco 415EX with Valmet 370E Processing Head2005 Timbco 415EX with Valmet 370E Processing Head. Frame hours are unknown, hour meter reads 6,508 hours. Sisu engine starts and runs good. Reversing fan in working order, new alternator. 24" double grouser pads, undercarriage is estimated at 85%. Pins, bushings, and swing bearing are tight. Squirt boom. Valmet 370E processing head is in good working order, one feed wheel motor could be resealed. Heat, A/C, radio, lights. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Timbco | 415EX | 2005 |
$54,900
|
![]() |
JOHN DEERE 643DJOHN DEERE 643D FELLER BUNCHER 6 CYL DEERE STEERING WHEEL STEER KOEHRING WATEROUS HEAD DRIVE PUMP IS OUT OF IT |
John Deere | 643D | - |
$16,500
|
![]() |
1997 VALMET 544X1997 VALMET 544X SINGLE BUNK FORWARDER 4 CYL FORD POWERSHIFT LEVER CONTROLS BYPASS BUCKET DOES HAVE WEAK TRANSMISSION |
Valmet | 544X | 1997 |
$25,000
|
![]() |
2010 PRENTICE 23462010 PRENTICE 2346 DOUBLE BUNK FORWARDER 4 CYL CAT POWERSHIFT JOYSTICK CONTROLS SQUIRT BOOM BYPASS BUCKET 23.1-26 FRT 600/55-26.5 REAR |
Prentice | 2346 | 2010 |
$169,000
|
![]() |
John Deere 440C Skidder1982 John Deere 440C Cable Skidder. Hour meter reads 5,021 hours but is incorrect. Reconditioned engine in 2021, along with replaced transfer gear, rebored steering cylinders, new engine oil cooler, hydraulic pump, winch brake, and rebuilt cab. 2" hitch receiver installed to tow a chipper. 125' swedge cable with Bullnose and four chain slides. 18.4x26 front tires are estimated at 95%, rear tires estimated at 70%. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
John Deere | 440C | 1982 |
$26,500
|
![]() |
Concept Products Shred-All 5600 Wood Chipper2006 Concept Products Shred-All 5600 Wood Chipper. This chipper was a state owned machine that was used for pallets. John Deere 6068T engine starts and runs good, 12' conveyor, 22" infeed roller diameter, 56" cutting drum, good tires and electric brakes. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Southwest USA. |
Concept Products | Shred-All 5600 | 2006 |
$90,000
|
![]() |
Loader and Sawbuck2015 CAT loader 559B DL4400 Classic Sawbuck $60,000.00 for both |
CAT | 559B | 2015 |
$60,000
|