Chippers For Sale
Featured in Chippers
Photo |
Title
|
Make | Model | Year | Price |
![]() |
Bandit 3590XL Whole Tree Chipper2010 Bandit 3590XL Whole Tree Chipper. Hour meter shows ~6500 hours. CAT C27 1050 HP w/ optional engine chip to 1370 HP. Engine runs and starts good. Hydronic engine preheated. PT tech clutch. Extended frame, to offset radiator from the engine. Hydraulic reversing fan which increases HP to the chip drum. Upgraded feedbox wall plates to 2" AR 450. Chip pocket upgrades, overs breakers. Overs breaker grates upgrade that bolt in at drum chute. The following upgrades were made at 6,467 hours. New brakes and bearings, new top side of chute, new drum belly wear plate, new infeed chain sprockets, new manifolds and studs 6,467 hours. 36+ inch chipping capacity. Set up for .75" chip size, 2.75+ tons per minute capacity. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA |
Bandit | 3590XL | 2010 |
$Call for Price
|
![]() |
Morbark 40/36 Whole Tree Chipper2009 Morbark 40/36 Whole Tree Chipper. This equipment has a John Deere 600 HP engine, 4,684 hours on machine, runs and starts good, strong hydraulics and pumps. Updated advantage 3 drum, rebuilt clutch, updated feed chain and drive sprocket, one size bigger. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. |
Morbark | 40/36 | 2009 |
$97,500
|
![]() |
Dynamic Model 585 23" Chipper2008 Dynamic Model 585 23" Chipper. Machine has a John Deere 500 HP. Fuel consumption ~8 gallons/hour. 30 ton chipping in 30-45 minutes depending on material. Chips tops very well with side feed rollers, 23" max capacity, 3 feed chains on feed bed, comes with remote control, chute is non-variable, always pointing 180 degrees from feed table. Grapple hook for moving with skidder, pintle hitch. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. |
Dynamic | 585 | 2008 |
$39,000
|
![]() |
Dynamic Cone-Head 570 Chipper2011 Dynamic Cone-Head 570 Chipper. Hour meter reads 596 hours, Cummins engine, runs and starts good, strong hydraulics and pump, extend the pull hitch so it could be pulled with a roll off truck but that can be shortened. Remote control to go with so you can run from the loading equipment, 34" In-Feed, 4-7" Blades, electric brakes. Contact Erik @ Red Pine Equipment 218-720-0933. Chipper is located in Northcentral USA. |
Dynamic | 570 | 2011 |
$46,500
|
![]() |
Peterson 5900 Whole Tree Chipper2008 Peterson 5900 Whole Tree Chipper. This chipper has a Reman CAT C18 engine with 4,000 hours, runs and starts good, strong hydraulics and cylinders, feed chain and rollers are all in good working order, new clutch, disc is in good condition. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Southeast USA. |
Peterson Pacific | 5900 | 2008 |
$87,500
|
![]() |
Trelan DL-18 Whole Tree Chipper1985 Trelan DL-18 Whole Tree Chipper. This equipment has a CAT 3406A engine, strong hydraulics, decent cylinders. tight disc bearing, new belts, couple sets of knives. Hood 7000 loader. Infeed and drive chain are in good working order. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in northcentral USA. |
Trelan | DL-18 | 1985 |
$39,500
|
![]() |
Roto Chopper B66 Chipper2011 Roto Chopper B66 Chipper. This chipper has 300 hours on a complete factory recondition, new engine, C16 CAT 785 HP, runs and starts good. New drive pumps and belts. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Rotochopper | B66 | 2011 |
$285,000
|
![]() |
Precision 58" 6 Knife ChipperPrecision 58" 6 Knife Chipper with Horizontal Feed Top Discharge. This equipment has no motor or shake table. Has an 8x8 screen table and all stand and mounts. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Precision | 58-15 | Unknown |
$13,500
|
![]() |
Vermeer WC2300 XL Whole Tree Chipper2014 Vermeer WC2300 XL Whole Tree Chipper. Hour meter reads 3,965 hours, CAT C13 440 HP Tier 3 Engine, runs and starts good. 5/8" cut babbitted knives, standard discharge chute. Trailer lighting, super single wheels, air compressor assembly. Includes enclosure and air dryer, remote. Well maintained. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Vermeer | WC2300 XL | 2014 |
$194,500
|
![]() |
Morbark 40/36 Whole Tree Chipper2010 Morbark 40/36 Whole Tree Chipper. This chipper has a 600 HP John Deere Engine, runs and operates good, 1,900 hours on the engine, 6,100 total hours. Feed wheel and drive gearbox are in good working order, new feed bed. Strong hydraulics and cylinders. Drum knife and holders are in good condition. Fully functional remote. Good tires and brakes, wiring is all in good shape. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Morbark | 40/36 | 2010 |
$135,000
|
![]() |
Morbark 30/36 Chipper Whole Tree Chipper2006 Morbark 30/36 Chipper Whole Tree Chipper. This equipment has a 12.5 liter John Deere engine, runs and starts good, hour meter reads 5,000 hours, strong hydraulics, feed system and feed chains are in good working order, tight pins and bushings on loader and grapple, drum and knives. Enclosed cab with joystick controls. Good tires and brakes. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Morbark | 30/36 | 2006 |
$75,500
|
![]() |
Bandit 1850 Tracked Chipper1998 Bandit 1850 Track 18” Disc Chipper. This machine has a John Deere 250 HP engine, runs and starts good, engine block heater, strong hydraulics, hour meter reads 3,500 hours. Machine was just gone through. Joystick controls, loader, lift Cylinder, rollers, tray shut, new knives, balanced drum. Continuous rotation grapple, electric throttle cable in cab, high angle discharge with hydraulic deflector, track type in-feed conveyor. New Lexon glass. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA. |
Bandit | 1850 | 1998 |
$85,000
|