Featured in Logging Equipment
Photo |
Title
|
Make | Model | Year | Price |
![]() |
CASE 1187C Feller Buncher1988 CASE 1187C Feller Buncher. This machine has a Cummins 8.3 engine, runs and starts good, 22" Rotto Saw Intermittent 40 degree tilt, newer undercarriage, tight pins and bushings. Runs good, hour meter reads 7,270 hours. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Southwest USA. |
CASE | 1187C | 1988 |
$23,900
|
![]() |
2014 Komatsu XT 430 Processor with Rolly II Head2014 Komatsu XT 430 W / Rolly 2 Head and New Woodland Eaton Computer System. 6800 Hours. Very Clean |
Komatsu | XT 430 | 2014 |
$Call for Price
|
![]() |
2016 Timberpro TN 725C w/ Rolly III Head2016 Timberpro TN725C W / Rolly 3 Head. Also has NEW Woodland Eaton Computer System. 6,200 hours. Very Nice |
Timberpro | TN725C | 2016 |
$300,000
|
![]() |
Mechanical DelimberStripper Manufacturing Mechanical Delimber. This delimber is designed to provides fast delimbing. Reversible, bolt-in 'Easy Slide" knives can be easily sharpened or changed. Rugged, lightweight head is easier on equipment. Maintenance is easy and inexpensive. Designed for fir, spruce, hemlock, pine, and similar species. Also works well on smaller hardwood species. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. |
Stripper | - | Unknown |
$6,500
|
![]() |
John Deere 440 C Cable Skidder1980 John Deere 440-C Cable Skidder. This skidder runs and starts good, 4 speed manual transmission, center section was rebuilt, strong hydraulics and cylinders. New clutch, axel seal, & shifting plate. Replaced drive shaft, neutral safety switch, and shut off switch. Good brakes. Strong winch. 18.4 x 26 tires @ 50% with a set of single diamond chains. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. |
John Deere | 440C | 1980 |
$19,500
|
![]() |
John Deere 753J Harvester with a JP Skidmore 4 Roller Head2014 John Deere 753J Harvester with a JP Skidmore 4 Roller Head. Hour meter reads 4,800 hours, runs and starts good, pre-heater, strong hydraulics and drive system, all cylinders are in good working condition. Very tight boom and head. New 2020 JP computer system. 24" double grouser pads. Undercarriage is @ 80%. Heat, A/C, lights, and radio. No welds. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
John Deere | 753J | 2014 |
$Call for Price
|
![]() |
2005 Ponsse Ergo Harvester2005 Ponsse Ergo with 2012 H6 Head. HN125 crane. Mercedes 6 cylinder engine. Heat & A/C. Wabasto pre-heater. Tires are 700/55-34 fronts & 710/45-26.5 rear. |
Ponsse | Ergo | 2005 |
$92,500
|
![]() |
John Deere 2054 with a 513 ProPac Delimber2006 John Deere 2054 with a 513 ProPac Delimber. Hour meter reads 9,000 hours, John Deere 6068T Tier II engine, runs and starts good, strong hydraulics and drive system. Cylinder's and pumps are in good working order. Tight newer boom 3,000 hours ago, new boom chain 500 hours ago, cables and rollers are in good working order. Topping and butt saw are in good condition, solid grab arms. Undercarriage is @ 50%, 28" double grouser pads. New gear box seal. Block heater, heat, A/C, and lights. Good Glass. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
John Deere | 2054 | 2006 |
$108,000
|
![]() |
Bandit 3590XL Whole Tree Chipper2010 Bandit 3590XL Whole Tree Chipper. Hour meter shows ~6500 hours. CAT C27 1050 HP w/ optional engine chip to 1370 HP. Engine runs and starts good. Hydronic engine preheated. PT tech clutch. Extended frame, to offset radiator from the engine. Hydraulic reversing fan which increases HP to the chip drum. Upgraded feedbox wall plates to 2" AR 450. Chip pocket upgrades, overs breakers. Overs breaker grates upgrade that bolt in at drum chute. The following upgrades were made at 6,467 hours. New brakes and bearings, new top side of chute, new drum belly wear plate, new infeed chain sprockets, new manifolds and studs 6,467 hours. 36+ inch chipping capacity. Set up for .75" chip size, 2.75+ tons per minute capacity. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA |
Bandit | 3590XL | 2010 |
$Call for Price
|
![]() |
John Deere 690ELC with a ProPac 453 Delimber1995 John Deere 690ELC with a ProPac 453 Delimber. This equipment has had a recent rebuilt engine, runs and starts good. Strong hydraulics and cylinders, straight boom, good cables, & topping saw. Newer planetary on swing gear, undercarriage is in good working order, decent pads. Joystick controls. Heat, A/C, and lights. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
John Deere | 690ELC | 1995 |
$29,500
|
![]() |
Hood S-182 Self Propelled Loader w/ Hood 60" Slasher1985 Hood S-182 Self Propelled Loader with a Hood 60" Pull Behind Slasher. This equipment runs and starts good, strong hydraulics and cylinder, decent boom and 1/3 cord Bypass grapple, dead heal. Lever controls. Carrier and drive system are in working order. Slasher has a straight blade and decent teeth. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Hood | S-182 | 1985 |
$24,000
|
![]() |
Rottne F15D Double Bunk Forwarder2019 Rottne F15D Double Bunk Forwarder. Hour meter reads 2,600 hours, runs and starts good, strong hydraulics and cylinders, no leaks. Bogies are all in good working order. Tight center section. Tight RK125 boom and grapple. Like new condition with a set of tracks included. Contact Aaron @ Red Pine Equipment 218-720-0933. Forwarder is located in Northeast USA. |
Rottne | F15D | 2019 |
$Call for Price
|