Sort By:   GridGallery
Photo Title
Make Model Year Price
Ponsse Ergo Processor

Ponsse Ergo Processor

2005 Ponsse Ergo Processor. This machine has a Mercedes Benz engine, runs and starts good, HN125 crane 73H head, strong hydraulics and drive system, tight boom and head, grab arms are in good working order, went through measuring system a year ago, cradles and axles are in good working order, tight center section, 710 tires @ 70% with tracks, front tires are @ 60%, Wabasto pre heater, fire suppression system, heat, A/C, and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Ponsse Ergo 2005
$125,900
2005 Timberjack 1270D Harvester

2005 Timberjack 1270D Harvester

TIMBERJACK 1270D WHEELED HARVESTER 6 CYL DEERE 758HD HEAD 700 RUBBER

Timberjack 1270D 2005
$64,900
John Deere 1070D Harvester

John Deere 1070D Harvester

John Deere 1070D Harvester with H754 processor head. Year: 2005. Approximately 10,300 hours. This machine was professionally restored in 2015/2016. Only 300 hours since restoration and is in full working order. Tires are in good condition, tracks are in good condition, chains for the rear tires are included but are worn. Full operator and repair manuals included. Cab has working A/C and Heat. New windshield, and side windows, brakes, and many, many other parts. This harvester was owned and operated by Irwin Post since 2015. Restored at Nortrax in Springfield VT, they are familiar with this machine. This Machine is very similar to the Deere 1270 harvester, just slightly smaller. Very productive machine. Asking price just reduced to $98,000.

John Deere 1070D 2005
$98,000
Ponsse Ergo Harvester with a H73E Harvesting Head

Ponsse Ergo Harvester with a H73E Harvesting Head

2005 Ponsse Ergo Harvester with a H73E Harvesting Head. This machine has a Mercedes Benz engine, runs and starts good, 17,000 hours, pre-heat system, strong hydraulics and cylinders, new main pump at 13,500 hours, new joystick controls, old ones to go with as spares, tight boom, H200 crane, 710 tires with Eco track and a set of rear chains. Head and measuring system are in good working order. Heat, A/C, and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA

Ponsse Ergo 2005
$110,000
Prentice 210E Loader

Prentice 210E Loader

2005 Prentice 210E Loader with a 60" Hanfab Slasher. This machine has a John Deere engine, runs and starts good, new bearings and oil seal, new fuel pump, hydraulic pump has been gone through, strong cylinders, tight boom and Rotobec grapple, tight joystick controls, slasher is in good working order. Carrier has good brakes, decent tires, heat, and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Prentice 210E 2005
$Call for Price
Timbco 415EX Processor with a Rolly II Head

Timbco 415EX Processor with a Rolly II Head

2005 Timbco 415EX Processor with a Rolly II Head. This equipment has a Susi engine, starts & runs good, strong hydraulics and cylinders, newer Main pump 3,000 hours, Pro Heat system. 2,500 hours on undercarriage, 24" DG pads, clean fix fan, tight boom. Head is in good working order, DASA 380 computer. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Timbco 415EX 2005
$87,500
Hydro Ax 470 Feller Buncher

Hydro Ax 470 Feller Buncher

2005 Hydro Ax 470 Feller Buncher. This machine has a Cummins engine, runs and starts good, new oil pan gasket, in-cooler, hydraulic cooler, new fan. Strong hydraulics and cylinders, joystick machine. 22" Head, 28Lx26 tires - 2 are new. Heat, A/C, and lights. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Hydro-Ax 470 2005
$44,500
Fabtek 346B Forwarder

Fabtek 346B Forwarder

2005 Fabtek 346B, 600 rear rubber, 28L front, 4 cly. Deere engine, 16864 hours

Fabtek 346B 2005
$Call for Price
Ponsse Ergo Harvester with a H73 Head

Ponsse Ergo Harvester with a H73 Head

2005 Ponsse Ergo Harvester with a H73 Head. This machine has a HN125 Crane, 19,000 hours, runs and starts good, tracks are @ 60%. New CPU, wiring on boom and head replaced last year, new feed rollers & chain auto tensioner last year, leveling system redone, new module and valves, fire suppression, new measuring system, new knives last year, heat, and A/C, all lights are operable. Camo covering on sheet metal. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Ponsse Ergo 2005
$110,000
John Deere 748GIII Grapple Skidder ***SOLD***

John Deere 748GIII Grapple Skidder ***SOLD***

2005 John Deere 748GIII Grapple Skidder. This machine runs and starts good, newer engine 2 years ago, newer pump and transmission, valve bank was redone, center section was done this spring, blade pins have some play, axles and cradles are in good working order. Tires 30.5x32 3 @ 75%, heat, A/C, and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD***

John Deere 748GIII 2005
$51,500
John Deere 648GIII Skidder ***SOLD***

John Deere 648GIII Skidder ***SOLD***

2005 John Deere 648GIII Dual Arch Grapple Skidder with Winch. This machine has a newer engine, runs and starts good, strong hydraulics and DD transmission, this machine is in good working order, tight center section, arch and steer cylinders have a little play not bad, LED lights, good 30.5x 32 tires @ 90% with 1 set of Bear claw chains, heat, & A/C. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD***

John Deere 648GIII 2005
$Call for Price
Valmet 425EX Feller Buncher ***SOLD***

Valmet 425EX Feller Buncher ***SOLD***

2005 Valmet 425EX Feller Buncher with a Quadco 22" 360 Head. This machine has a newer Cummins engine, new oil cooler, Espar pre heater, strong hydraulics, main pump is in good working order. Recent replacements include: both track pumps last March and 2 final drives. Strong cylinders, main boom cylinder has been rebuilt, 28" pads, idlers. Quadco head is in good working order, straight disc - good teeth. Heat, A/C, and extra lights. Well maintained. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. ***SOLD***

Valmet 425EX 2005
$89,500