Sort By:   GridGallery
Photo Title
Make Model Year Price
Valmet 941 Harvester

Valmet 941 Harvester

2007 Valmet 941 Harvester Approximately 9400 hours 370.2 Head One set of Tracks Xeon Lights Has protective bars over Hood Self leveling Cab Ac Heat Heated Seat AM FM disc Extra Bars and Chains Very good condition!

Valmet 941 Harvester 2007
$125,000
CAT 525C Skidder

CAT 525C Skidder

2007 CAT 525C Single Arch Grapple Skidder with a Winch. Hour meter reads 10,500 hours, runs and starts good, transmission is in good order, strong hydraulics and cylinders, center and arch has some play - normal wear, grapple and winch are in good working order, tight controls, heat, A/C may need to be charged, 30.5 x 32 tires, DD chains and SD chains, DD chains new, will need a new left door. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

CAT 525C 2007
$47,500
Hood S-182 Self Propelled Loader Slasher

Hood S-182 Self Propelled Loader Slasher

2007 Hood S-182 Self Propelled Loader Slasher. This is a one owner machine, runs and starts good, self propelled carrier works but only has 4 wheel drive currently, adjustable flip board for different length logs. 60"blade, new saw motor, tight boom and grapple, heat. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Hood S182 2007
$49,900
Morbark 23 WCL Whole Tree Chipper

Morbark 23 WCL Whole Tree Chipper

2007 Morbark 23 WCL Whole Tree Chipper. This equipment has a CAT 3412 850 HP engine, runs and starts good, engine was turned down to 850, new clutch, knifes and disc are in good working order, hydraulics & feed wheel are in good condition, remote control, hydraulic swivel/telescoping discharge spout, good brakes and tires. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Morbark 23 WCL 2007
$195,000
Valmet 425EXL Processor

Valmet 425EXL Processor

2007 Valmet/Timbco 425EXL Processor. This machine has 100 hours on a new Cummins 8.3 engine, new pumps, 1,000 hours on new undercarriage, new final drives and motors, Rolly II head and Dasa measuring system are all in good order, has little pin play on the leveling, working every day, dry machine. For more information contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA.

Timbco 425EXL 2007
$162,500
Ponsse Buffalo Forwarder

Ponsse Buffalo Forwarder

2007 Ponsse Buffalo Log Forwarder with 11,000 hours. 700 rubber @ 50%, 65% set of EcoTracks, K90+ crane, Ponsse 36 bucket. Pins and bushings are in very good shape throughout machine. Rear end replaced, transmission, pump, complete hydrostat replaced. Preheater installed. Extendable bunks. Dry machine. Ready to work. Contact Aaron @ Red Pine Equipment 218-720-0933. machines i located in Northeast USA.

Ponsse Buffalo 2007
$182,500
CAT 553 Feller Buncher

CAT 553 Feller Buncher

2007 CAT 553 Feller Buncher. This machine has 8,682 hours, runs and starts good, strong hydraulics, pretty tight center section. Has a Prentice SH-50 head 20" in good working order, steering wheel, 28Lx26 tires @ 40%, heat, A/C, and lights. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

CAT 553 2007
$52,000
2007 John Deere 703G Feller Buncher

2007 John Deere 703G Feller Buncher

JOHN DEERE 703G FELLER BUNCHER FS20 HEAD 6081 DEERE 6 CYL 181 HP

John Deere 703G 2007
$165,000
CAT 525C Grapple Skidder ***SOLD***

CAT 525C Grapple Skidder ***SOLD***

2007 CAT 525C Grapple Skidder with Winch. This skidder has 9,000 hours, runs and starts good, strong hydraulics and transmission, winch is in good working order may need a few bells, tight center section, grapple is tight, continuous rotation. Tires are good all the way around, heat, A/C, and radio. Door is removed. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD***

CAT 525C 2007
$37,500
Rottne H20 Harvester with a Maskiner SP 761 Head

Rottne H20 Harvester with a Maskiner SP 761 Head

2007 Rottne H20 Harvester with a Maskiner SP 761 Head. Hour meter reads 11,000 hours, runs and starts good, pre-heater, 3,000 hours ago: new injectors, water pump, wiring harness, new hoses, strong hydraulics and cylinder. Newer pump, tight boom and head, boom has been re-bushed, SP computer and measuring system, head has good rollers and grab arms, leveling system is in good condition, heat, A/C, and lights. Well maintained. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Canada.

Rottne H20 2007
$225,500
Prentice 2470 Feller Buncher ***SOLD***

Prentice 2470 Feller Buncher ***SOLD***

2007 Prentice 2470 Feller Buncher. Hour meter reads 4,706 hours, runs and starts good, strong hydraulics and cylinders, joystick controls, tight center section, head and saw blade are in good order, tires are @ 50%, heat, A/C, and lights. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Southeast USA. ***SOLD***

Prentice 2470 2007
$39,500
Concept Products Shred All D5600 Horizontal Grinder *SOLD*

Concept Products Shred All D5600 Horizontal Grinder *SOLD*

2007 Concept Products Shred All D5600 Horizontal Grinder. This equipment has 692 hours, 6 cyl. John Deere turbo diesel engine, approx 175 HP. Remote feed and manual feed, magnetic discharge head. Belts are in great shape, recent service, extra replaceable teeth, 2" screen, easy set up and portability. Rear conveyor slides under machine for easier transport and storage. Can be pulled by pick up truck, has electric trailer brakes. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipmentt is located in Northeast USA. ***SOLD***

Concept Products Shred All D5600 2007
$72,500