Chippers For Sale
Featured in Chippers
| Photo |
Title
|
Make | Model | Year | Price |
|
Vermeer WC2500TX Track Chipper2022 Vermeer WC2500TX Track Chipper. Hour meter reads 300 hours. Cummins 600 HP. Tier4f engine. Microchip & Macrochip drums for variable chip sizes. Dual infeed conveyor is in good condition. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Vermeer | WC2500TX | 2022 |
$525,000
|
|
Terex TBC430T Self-Propelled Chipper2014 Terex TBC430T Self-Propelled Chipper. Hour meter reads 2,523 hours. CAT C18 engine with 765 HP. Remote control included. New valve banks. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Canada. |
Terex | TBC430T | 2014 |
$325,000
|
|
Concept Products Shred-All 5600 Wood Chipper2006 Concept Products Shred-All 5600 Wood Chipper. This chipper was a state owned machine that was used for pallets. John Deere 6068T engine starts and runs good, 12' conveyor, 22" infeed roller diameter, 56" cutting drum, good tires and electric brakes. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Southwest USA. |
Concept Products | Shred-All 5600 | 2006 |
$90,000
|
|
Rayco RG1220 Brush Chipper2011 Rayco RG1220 Brush Chipper. Hour meter reads 225 hours. Kubota 66.8 HP engine starts and runs good. Pre-emission engine. 12" chipping capacity with a 12"x20" in-feed opening. Intake rate of 100 fpm. Discharge swivels 360° and at a discharge height of 112". Feed wheel lift and crush handles on both sides. New battery. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Rayco | RG1220 | 2011 |
$38,500
|
|
Morbark Mountain Goat 20/36 Track Chipper2004 Morbark Mountain Goat 20/36 Track Chipper. Hour meter reads 1,648 hours. Cummins QSL11 400hp. Morlift 150 loader. Feed chain is in good condition. Undercarriage is estimated at 75%. Heat, A/C. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Morbark | Mountain Goat 20/36 | 2004 |
$113,500
|
|
Morbark Model 23 NCL Chipper ***SOLD***1997 Morbark Model 23 NCL Chipper. This machine has 4,200 hours, CAT 550 engine, runs and starts good. Machine was rebuilt in contractors shop 800 hours ago including the following items: new wear plates, belly pans and head liners, new clutch, new in-feed rollers, wireless remote. Chute is in good condition. Dirt separator, this chipper is in excellent shape for the age, produces a very consistent chip. Set up for 7/8" chip currently. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD*** |
Morbark | Model 23 | 1997 |
$94,900
|
|
Morbark Model 16 Disc ChipperMorbark Model 16 Disc Chipper. Hour meter reads 3,500 hours. CAT 3208 engine starts and runs good. Loader with cab. Loader has a rotator for grapple installed with additional pedal. Two chutes included, one for piles and one to load trucks. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Morbark | Model 16 | Unknown |
$36,500
|
|
Bandit Intimidator 15XP Chipper2021 Bandit Intimidator 15XP Chipper. Hour meter reads 1,543 hours. Ford 6.2L 165 HP engine. 37" diameter drum, 2 knife split pocket 5/8" chip. Single axle allow for towing as non-CDL trailer. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Bandit | Intimidator 15XP | 2021 |
$49,500
|
|
Precision Husky Chipper1992 Precision Husky Chipper. Hours are unknown. KT 600 HP engine starts and runs good. New batteries, oversized cables, master switch, oversized starter, pockets, knife clamps, and counter knives, digital volt meter, and re-cored radiator within the last year. New bearings in feed rear feed wheel, a few new sprockets, drive chains, drive motors for the top feed wheel, rebuilt injector pump, and new hydraulic pump belts within the last 8 months. Also has a new shaft and bearings on the bottom feed wheel. 23" throat. Will fill 42 ton in 30-40 minutes depending on the wood. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Precision | Husky | 1992 |
$60,000
|
|
Trelan DL-18 Whole Tree Chipper1985 Trelan DL-18 Whole Tree Chipper. This equipment has a CAT 3406A engine, strong hydraulics, decent cylinders. tight disc bearing, new belts, couple sets of knives. Hood 7000 loader. Infeed and drive chain are in good working order. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in northcentral USA. |
Trelan | DL-18 | 1985 |
$34,000
|
|
Vermeer BC1800XL Tow Behind Chipper2022 Vermeer BC1800XL Tow Behind Chipper. PSI 165 HP 5.7L engine. Hour meter reads 1,151 hours. 18" chipping capacity. 4 knife, with 19" material capacity. Unit is work ready. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Vermeer | BC1800XL | 2022 |
$77,500
|
|
Vermeer BC1800XL Chipper ***SOLD***2022 Vermeer BC1800XL Chipper. Hour meter reads 310 hours. 173 HP John Deere diesel. 18in feed opening, swivel discharge chute. Knives have been flipped. Serviced at 275 hours. Brand new knife kit, filters and a spare new rim for additional cost. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. ***SOLD*** |
Vermeer | BC1800XL | 2022 |
$82,500
|