Sort By:   GridGallery
Photo Title
Make Model Year Price
John Deere 648G Skidder

John Deere 648G Skidder

1998 John Deere 648G Dual Arch Grapple Skidder. Hour meter reads 18,094 hours, grapple resealed and new grapple brakes, has winch but no drive shaft, 14 bolt rims and 30.5 x 32 tires in good condition, 2 are new, & 2 are @ 60-70%, completely gone through last breakup, heat, lights, no AC. Plug in block heater. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

John Deere 648G 1998
$33,000
CAT 525 Swing Grapple Skidder

CAT 525 Swing Grapple Skidder

1998 CAT 525 Swing Grapple Skidder. Engine and transmission were rebuilt 8,300 hours ago. Differentials and hydraulic pumps 3,800 hours ago. Decent center section, strong cylinders, Esco swing boom grapple are in good working order. 30.5 tires @ 15% remaining with chains all around. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Canada.

CAT 525 1998
$26,000
Valmet 644 Forwarder

Valmet 644 Forwarder

1998 Valmet 644 Forwarder. This machine has a Cummins 4BT engine, runs and starts good, Power Shift transmission, strong hydraulics and cylinders, new starter, resealed valve bank, rebuilt stick and main cylinders, set of chains for front. 2 spare 23.1 x 26 tires and one extra 44. Newer charge pump, newer boom, tight pins and bushings, SureGrip grapple bypass, tight center section, joystick controls. Stacking blade. Heat, A/c, lights, and radio. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Valmet 644 1998
$Call for Price
Valmet 646 Forwarder

Valmet 646 Forwarder

1998 Valmet 646 forwarder. Cummins 3.9 engine. Powershift transmission. Joystick controls. Cranab 650 XL loader w/SuperGrip 260 bucket. Tires are 23.1X26 on front & 600mm on rear.

Valmet 646 1998
$52,000
Valmet 644 Single Bunk 8 Ton Forwarder

Valmet 644 Single Bunk 8 Ton Forwarder

1998 Valmet 644 Single Bunk 8 Ton Forwarder. This machine has a Cummins 4BT engine, runs and starts good, new radiator, Power Shift transmission is in good working order, tight center section, new charge pump, strong hydraulics and cylinders, few minor seeps, Pro Heat system, tight controls, Cranab 650XL extenda boom, 360 Cranab bypass grapple, new 23.1x26 tires. Heat, A/C, and lights. Strong clean machine. Contact Aaron @ Red Pine Equipment 218-720-0933. Truck is located in Northcentral USA.

Valmet 644 1998
$59,500
John Deere 648GII Skidder

John Deere 648GII Skidder

1998 John Deere 648GII Dual Arch Grapple Skidder. This skidder has a newer 6068T John Deere, runs and starts good, strong hydraulics and cylinders, strong PowerShift transmission, decent center section has a little play, arch and grapple are in good order, axles and cradles are in good working condition. 30.5x32 tires @60-75% with a set of chains. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

John Deere 648GII 1998
$36,500
John Deere 748G Skidder

John Deere 748G Skidder

1998 John Deere 748G Dual Arch Grapple Skidder. This machine has 3,500 hours on a new John Deere crate engine, pump was done at the same time, strong hydraulics and cylinders, tight center section, arch and grapple are in good working order, strong transmission, 30.5x32 tires with chains, heat, lights, and radio. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

John Deere 748G 1998
$39,500
1998 Valmet 544X Forwarder

1998 Valmet 544X Forwarder

VALMET 544X SINGLE BUNK FORWARDER 4 CYL FORD COMPLETELY REBUILT LEVER CONTROLS HEAT AND AIR NEW CENTER PINS AND BUSHINGS

Valmet 544X 1998
$49,900
Timbco T445-C Feller Buncher

Timbco T445-C Feller Buncher

1998 Timbco T445-C Feller Buncher. This equipment has a Cummins 8.3 engine, runs and starts good, 11,400 hours, strong hydraulics and cylinders, Quadco 22B Head continuous rotation in good working order, straight disc has new teeth. Undercarriage is @ 75%, new sprockets 400 hours ago, 28" single grouser pads. Boom has been replaced, all pumps are in working order. Has a little play in one leveling shaft. Heat, A/C, & lights. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA.

Timbco T445-C 1998
$74,500
Morbark 23 NCL Chiparvestor

Morbark 23 NCL Chiparvestor

1998-99 Morbark 23 NCL Chiparvestor. This machine has a CAT 3412 engine, 850 HP, runs and starts good, hour meter reads 7,600 hours, twin turbos, strong hydraulics, drum and feed rollers are in good order, knife could use sharpening, decent brakes and tires. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Morbark 23 NCL 1998
$109,500
Valmet 644 Forwarder ***SOLD***

Valmet 644 Forwarder ***SOLD***

1998 Valmet 644 Forwarder. This equipment has a Cummins 4BT engine, runs and starts good, Power Shift transmission, strong hydraulics and cylinders, new charge pump, main is in good working order. Newer boom, tight pins and bushings, SureGrip grapple bypass, tight center section, joystick controls. stacking blade. Heat, A/C, lights, and radio. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD***

Valmet 644 1998
$49,500
Franklin 132 Forwarder ***SOLD***

Franklin 132 Forwarder ***SOLD***

1998 Franklin 132 Single Bunk Forwarder. This machine has a new 4BT Cummins engine less than 1 year old, runs and starts good, Power Shift transmission has been rebuilt, tight boom and bypass grapple, tight center section, strong hydraulics and cylinders, valve body will need some attention. New 23.1x26 tires on rear front are @60%, heat. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA. ***SOLD***

Franklin 132 1998
$29,500