Chippers For Sale
| Photo |
Title
|
Make | Model | Year | Price |
|
Precision Husky Chipper1992 Precision Husky Chipper. Hours are unknown. KT 600 HP engine starts and runs good. New batteries, oversized cables, master switch, oversized starter, pockets, knife clamps, and counter knives, digital volt meter, and re-cored radiator within the last year. New bearings in feed rear feed wheel, a few new sprockets, drive chains, drive motors for the top feed wheel, rebuilt injector pump, and new hydraulic pump belts within the last 8 months. Also has a new shaft and bearings on the bottom feed wheel. 23" throat. Will fill 42 ton in 30-40 minutes depending on the wood. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Precision | Husky | 1992 |
$60,000
|
|
Morbark 30/36 Whole Tree Drum Chipper2009 Morbark 30/36 Whole Tree Drum Chipper. Hour meter reads 4,194 hours. John Deere 440hp engine. Drum is in good condition. Infeed chain is estimated at 90%. Includes wired and wireless radio remote controls. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Southeast USA. |
Morbark | 30/36 | 2009 |
$90,000
|
|
Bandit 2290TK Track Chipper ***ON HOLD***2015 Bandit 2290TK Track Chipper. Hour meter reads 4,850 hours. John Deere RG6135 525hp engine. Newer clutch with around 750 hours. 24" single grouser pads, undercarriage is estimated at 75%. Drum is in good condition. Ready to work. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. ***ON HOLD*** |
Bandit | 2290TK | 2015 |
$Call for Price
|
|
Morbark 40/36 Drum Chipper ***SOLD***2011 Morbark 40/36 Drum Chipper. Hour meter reads 3,700 hours. CAT C18 engine starts and runs good. Advantage 3 drum is in good condition. 23" chipping capacity. 40"x39" infeed opening. Hydraulic knuckleboom loader with 23' extended boom reach. 2537 log grapple with 360° continuous rotation. Single grouser pads, undercarriage is estimated at 70%. Valve banks are dry and clean. Espar preheater. Enclosed cab has heat & A/C. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. ***SOLD*** |
Morbark | 40/36 | 2011 |
$Call for Price
|
|
Morbark 22 RXL Chipper1993 Morbark 22 RXL Chipper. Cummins engine with newer overhaul. Engine has a knock or possible clutch issue. Pan needs to be dropped and inspected. Feed chain is estimated at 40%. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Morbark | 22RXL | 1993 |
$58,500
|
|
Morbark 2355 Flail Chiparvestor2012 Morbark 2355 Flail Chiparvestor. Hour meter reads 17,000 hours. CAT C27 engine that was gone through a few years ago. 3 knife, liners are good, flails are in good condition. New PTO system in 2022. Needs new rubbers inside the flails. Includes spare bearings, conveyor chains, flail rods, & filters. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Southcentral USA. |
Morbark | 2355 | 2012 |
$270,000
|
|
Morbark 2755 Flail Chiparvestor2013 Morbark 2755 Flail Chiparvestor. Hour meter reads ~15,000 hours. CAT 27 875hp engine. 3 knife chipper disc option. Recently rebuilt gearbox and new spouts. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Southcentral USA. |
Morbark | 2755 | 2013 |
$357,500
|
|
Morbark 22RXL Whole Tree Chipper1979 Morbark 22RXL Whole Tree Chipper. Full factory rebuild in 2004. CAT 3412, 800 HP engine. Twin disc clutch. Feed roller bearings, knives, & feed chains are in good condition. Produces 7/8" chips. 2014 Hood 8000 loader with Heat & A/C. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Morbark | 22RXL | 1979 |
$95,000
|
|
Bandit 2590 Chipper2012 Bandit 2590 Chipper. This chipper has a CAT C-15, 540 HP Engine, hour meter reads 4,633 hours and is still in use. Newer remote control kit, exhaust manifold, turbo, and clutch discs. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Bandit | 2590 | 2012 |
$175,000
|
|
Rayco RG1220 Brush Chipper2011 Rayco RG1220 Brush Chipper. Hour meter reads 225 hours. Kubota 66.8 HP engine starts and runs good. Pre-emission engine. 12" chipping capacity with a 12"x20" in-feed opening. Intake rate of 100 fpm. Discharge swivels 360° and at a discharge height of 112". Feed wheel lift and crush handles on both sides. New battery. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Rayco | RG1220 | 2011 |
$38,500
|
|
Bandit 280 Chipper with Grapple & Winch2005 Bandit 280 Chipper with Grapple & Winch. Hour meter reads 1,300 hours on engine, 875 hours on auto feed. Newer 275 HP engine was installed. Includes extra knives, anvil, & bolts. Pintle hitch. Rated for 18" logs but can chip bigger. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast. |
Bandit | 280 | 2005 |
$84,500
|
|
Morbark 23NCL Whole Tree Chipper1994 Morbark 23NCL Whole Tree Chipper. 850 HP CAT 3412 with 4,600 hours on in-frame overhaul. Top feed chute. Front of engine resealed. New drive belt and Poly chain. Does not burn any oil. Starts well in cold weather. Cooling system in good shape. Clutch in good shape. All new liners in 2021 on the chipper. Babbit 8 knife system installed. New remote system installed that controls all moving parts on the chipper. 8 knife disc is in good shape, set up for 7/8" chips. AR 450 face plates on disc less than 3 years old. New bearings on feed rollers, sprockets and chains recently replaced. Frame is in good shape. Air compressor included. Tires are in good shape and owner will check hubs and brakes at time of sale. Chipper was converted from a WCL, professionally done. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is lcoated in Canada. |
Morbark | 23NCL | 1994 |
$112,500
|