Sort By:   GridGallery
Photo Title
Make Model Year Price
Precision Husky Chipper

Precision Husky Chipper

1992 Precision Husky Chipper. Hours are unknown. KT 600 HP engine starts and runs good. New batteries, oversized cables, master switch, oversized starter, pockets, knife clamps, and counter knives, digital volt meter, and re-cored radiator within the last year. New bearings in feed rear feed wheel, a few new sprockets, drive chains, drive motors for the top feed wheel, rebuilt injector pump, and new hydraulic pump belts within the last 8 months. Also has a new shaft and bearings on the bottom feed wheel. 23" throat. Will fill 42 ton in 30-40 minutes depending on the wood. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

Precision Husky 1992
$62,500
Morbark 40/36 Whole Tree Drum Chipper

Morbark 40/36 Whole Tree Drum Chipper

2009 Morbark 40/36 Whole Tree Drum Chipper. Hour meter reads 5,500 hours. Newer CAT C15 630 HP engine has 4,000 hours. Newer style Vantage drum is in good condition. Anvil has been redone & upgraded bed chains at 4,000 hours. New clutch disc in 2022. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Morbark 40/366 2009
$177,500
Vermeer BC1800XL Chipper

Vermeer BC1800XL Chipper

2022 Vermeer BC1800XL Chipper. Hour meter reads 310 hours. 173 HP John Deere diesel. 18in feed opening, swivel discharge chute. Knives have been flipped. Serviced at 275 hours. Brand new knife kit, filters and a spare new rim for additional cost. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

Vermeer BC1800XL 2022
$82,500
Morbark 22RXL Whole Tree Chipper

Morbark 22RXL Whole Tree Chipper

1979 Morbark 22RXL Whole Tree Chipper. Full factory rebuild in 2004. CAT 3412, 800 HP engine. Twin disc clutch. Feed roller bearings, knives, & feed chains are in good condition. Produces 7/8" chips. 2014 Hood 8000 loader with Heat & A/C. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Morbark 22RXL 1979
$95,000
Vermeer WC2300XL Whole Tree Chipper ***SOLD***

Vermeer WC2300XL Whole Tree Chipper ***SOLD***

2013 Vermeer WC2300XL Whole Tree Chipper. Hour meter reads 5,587 hours. CAT C13 440hp engine. Brand new turbo and filters. Newer infeed chain bearings and infeed chain. Knives are in good condition. Smart feed. 23" capacity drum style chipper. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. ***SOLD***

Vermeer WC2300XL 2013
$Call for Price
Vermeer WC2300XL Chipper ***SOLD***

Vermeer WC2300XL Chipper ***SOLD***

2015 Vermeer WC2300XL Whole Tree Chipper. Hour meter reads 1,372 hours. CAT C13 440 HP engine. Chipper features wireless remote, smart feed, and 23" capacity drum style chipper, 8 knife. Feed drum is very sharp, feed chain is tight. Babbitt plate and 2.5 sets of knives will be included. All liners have been recently replaced. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. ***SOLD***

Vermeer WC23000XL 2015
$Call for Price
Bandit 2590 Chipper

Bandit 2590 Chipper

2012 Bandit 2590 Chipper. This chipper has a CAT C-15, 540 HP Engine, hour meter reads 4,633 hours and is still in use. Newer remote control kit, exhaust manifold, turbo, and clutch discs. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

Bandit 2590 2012
$175,000
Rayco RG1220 Brush Chipper

Rayco RG1220 Brush Chipper

2011 Rayco RG1220 Brush Chipper. Hour meter reads 225 hours. Kubota 66.8 HP engine starts and runs good. Pre-emission engine. 12" chipping capacity with a 12"x20" in-feed opening. Intake rate of 100 fpm. Discharge swivels 360° and at a discharge height of 112". Feed wheel lift and crush handles on both sides. New battery. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

Rayco RG1220 2011
$38,500
Bandit 280 Chipper with Grapple & Winch

Bandit 280 Chipper with Grapple & Winch

2005 Bandit 280 Chipper with Grapple & Winch. Hour meter reads 1,300 hours on engine, 875 hours on auto feed. Newer 275 HP engine was installed. Includes extra knives, anvil, & bolts. Pintle hitch. Rated for 18" logs but can chip bigger. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast.

Bandit 280 2005
$84,500
Morbark 23NCL Whole Tree Chipper

Morbark 23NCL Whole Tree Chipper

1994 Morbark 23NCL Whole Tree Chipper. 850 HP CAT 3412 with 4,600 hours on in-frame overhaul. Top feed chute. Front of engine resealed. New drive belt and Poly chain. Does not burn any oil. Starts well in cold weather. Cooling system in good shape. Clutch in good shape. All new liners in 2021 on the chipper. Babbit 8 knife system installed. New remote system installed that controls all moving parts on the chipper. 8 knife disc is in good shape, set up for 7/8" chips. AR 450 face plates on disc less than 3 years old. New bearings on feed rollers, sprockets and chains recently replaced. Frame is in good shape. Air compressor included. Tires are in good shape and owner will check hubs and brakes at time of sale. Chipper was converted from a WCL, professionally done. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is lcoated in Canada.

Morbark 23NCL 1994
$112,500
Morbark 23WCL Whole Tree Chipper

Morbark 23WCL Whole Tree Chipper

1995 Morbark 23WCL Whole Tree Chipper. Hour meter reads 2,604 hours. CAT 3412 engine starts and runs good. Disc chipper. 30 knives included. Also includes a jig to solder knives. Brand new anvil. 3 knife system, 3/4 chip size. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

Morbark 23WCL 1995
$175,000
Trelan 23 Whole Tree Chipper

Trelan 23 Whole Tree Chipper

1988 Trelan 23 Whole Tree Chipper. CAT 500hp engine. Feed drums are in good condition. 3 knives. New clutch and belts. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

Trelan 23 1988
$Call for Price