Sort By:   GridGallery
Photo Title
Make Model Year Price
Tigercat 620C Skidder

Tigercat 620C Skidder

2007 Tigercat 620C Dual Arch Grapple Skidder. This machine has been completely gone through, engine and pumps, rear end was just redone, strong hydraulics and cylinders, tight center and arch pins, square stock grapple, 30.5x 32 tires @ 50% chains all around @ 60%. Heat,A/C, and lights. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA.

Tigercat 620C 2007
$54,500
Timberjack 380B Grapple Skidder ***SOLD***

Timberjack 380B Grapple Skidder ***SOLD***

1993 Timberjack 380B Grapple Skidder with Winch. This skidder has a recently rebuilt Cummins 6BT engine, runs and starts good, 4 speed Power Shift transmission in good working order, newer center section, strong steer and blade cylinders, few minor leaks. John Deere T40 winch in good working order, newer drive shaft, 28Lx26 tires @ 40%. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA. ***SOLD***

Timberjack 380B 1993
$32,500
Tigercat 630C Skidder

Tigercat 630C Skidder

2005 Tigercat 630C Dual Arch Grapple Skidder. This equipment has a newer crate Cummins engine with 4,000 hours, runs and starts good, strong hydraulics, new joystick and wiring, tight pins and bushings, strong transmission, cylinders are in good working condition, tires are 30.5x32 @ 50% with chains @ 40%, heat, and A/C. Contact Erik @ Red Pine Equipment 218-720-0933. Machine located in Northeast USA.

Tigercat 630C 2005
$46,500
Link Belt 210X2 Processor with Southstar QS500 Head

Link Belt 210X2 Processor with Southstar QS500 Head

2013 Linkbelt 210X2 Processor with Southstar QS500 Head. This machine has 9,691 hours, runs and starts good, head reseal & major cylinders have been done, dry machine, newer main hydraulic pump, undercarriage is in good working order, tight boom, head is in good working condition, heat, A/C, lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Canada.

Link Belt 210X2 2013
$198,500
Morbark Model 23 NCL Chipper

Morbark Model 23 NCL Chipper

1997 Morbark Model 23 NCL Chipper. This machine has 4,200 hours, CAT 550 engine, runs and starts good. Machine was rebuilt in contractors shop 800 hours ago including the following items: new wear plates, belly pans and head liners, new clutch, new in-feed rollers, wireless remote. Chute is in good condition. Dirt separator, this chipper is in excellent shape for the age, produces a very consistent chip. Set up for 7/8" chip currently. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Morbark Model 23 1997
$94,900
John Deere 540B Forwarder

John Deere 540B Forwarder

1989 John Deere 540B Single Bunk Forwarder. This machine runs and starts good, strong hydraulics and transmission, all cylinders are in good order, no major leaks, tight boom and grapple, rotator leaks a bit not bad, 23.1 x 26 tires @ 80%. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

John Deere 540B 1989
$27,500
Woodchuck Hyroller 1200 Chipper

Woodchuck Hyroller 1200 Chipper

2005 Woodchuck Hyroller 1200 Chipper. Hour meter reads 1,317 hours, equipped with a 70 HP Perkins diesel engine,12"x12" mouth, 5,200 LBS., good rubber. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA.

Woodchuck Hyroller 1200 2005
$14,500
CTR Delimber on Trailer with Topping Saw

CTR Delimber on Trailer with Topping Saw

CTR Delimber on Trailer with Topping Saw in good working order. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

CTR - -
$13,500
John Deere 648GIII Skidder ***SOLD***

John Deere 648GIII Skidder ***SOLD***

2005 John Deere 648GIII D/A Grapple Skidder with Winch. This skidder has 14,000 frame hours, 3,600 hours on engine and DD transmission, new fuel pump, strong hydraulics and winch, new center section, 30.5x32 tires @ 50% with chains, heat, A/C, and lights. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA. ***SOLD***

John Deere 648GIII 2005
$52,900
Timberpro 725C Processor with Rolly III Head ***SOLD***

Timberpro 725C Processor with Rolly III Head ***SOLD***

2016 TimberPro 725C Processor with a Rolly 3 Head, ~2,100 hours. Woodland cpu, 28" double grouser pads, clean fix fan, Espar preheater - engine, cab, hydraulics, Xenon light package, fire suppression, air ride heated/cooled seat, high speed saw. Cummins 8.3 engine. Very clean, straight and dry machine. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD***

Timberpro 725C 2016
$400,000
John Deere 548GIII Skidder ***ON HOLD***

John Deere 548GIII Skidder ***ON HOLD***

2007 John Deere 548GIII Grapple Skidder. Hour meter reads 2,803 hours, runs and starts good, strong hydraulics and transmission, no leaks, 28Lx26 tires, chains all around. Heat, A/C, and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA. ***ON HOLD***

John Deere 548GIII 2007
$175,000
Timberjack 404 Cable Skidder

Timberjack 404 Cable Skidder

1970 Timberjack 404 Cable Skidder. This machine has a Detroit 453 engine, runs and starts good, strong hydraulics and Allison auto 3 speed transmission, tight center section, Gearamatic model 19 winch, like new 18.4x34 tires. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northwest USA.

Timberjack 404 1970
$16,500