| Photo |
Title
|
Make | Model | Year | Price |
|
Tigercat 630H Skidder2023 Tigercat 630H Grapple Skidder. Hour meter reads 1,800 hours. 35.5x32 tires are estimated at 80%. Webasto preheat system. 21 cubic foot grapple. Reversing fan. Heat, A/C, radio, lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA. |
Tigercat | 630H | 2023 |
$315,000
|
|
Barko 295 Loader with CSI Delimber & Bucksaw2003 Barko 295 Loader with CSI Delimber & Bucksaw. Hour meter reads 11,000 hours. Cummins 6BT engine starts and runs good. Delimber and bucksaw are in good condition. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Southeast USA. |
Barko | 295 | 2003 |
$43,500
|
|
International with Rear Mount Prentice F-90T Loader1989 International with Rear Mount Prentice F-90T Loader. Cummins LTA10 engine starts and runs good. Tri-axle with drop axle, 11R22.5 tires are estimated at 90%. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Prentice | F-90T | - |
$33,900
|
|
60" Slasher Bucksaw Combo60" Slasher Bucksaw Combo. 21' length. Blade pumps are in good condition, unit works as it should. Pintle hitch. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
- | 60" | - |
$17,500
|
|
Precision Husky Chipper1992 Precision Husky Chipper. Hours are unknown. KT 600 HP engine starts and runs good. New batteries, oversized cables, master switch, oversized starter, pockets, knife clamps, and counter knives, digital volt meter, and re-cored radiator within the last year. New bearings in feed rear feed wheel, a few new sprockets, drive chains, drive motors for the top feed wheel, rebuilt injector pump, and new hydraulic pump belts within the last 8 months. Also has a new shaft and bearings on the bottom feed wheel. 23" throat. Will fill 42 ton in 30-40 minutes depending on the wood. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Precision | Husky | 1992 |
$60,000
|
|
Prentice 2384B w/ CSI 4400 Buck Saw & CTR 426 Delimber2012 Prentice 2384B Loader with CSI 4400 Buck Saw and CTR 426 Delimber. Hour meter reads 14,000 hours. Reman hydraulic pump and pilot pump. Boom is straight, minimal slack. CSI 4400 Buck Saw with an 18' table. CTR 426 delimber is in good working order. John Evans trailer. Cab has heat, A/C, radio, lights. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Southeast USA. |
Prentice | 2384B | 2012 |
$43,500
|
|
Tigercat 620E Skidder2016 Tigercat 620E Grapple Skidder with Winch. Hour meter reads 9,545 hours. New reman Cummins and turbo with less than 30 hours. 30.5x32 tires are estimated at 75%. Heat, A/C, radio, & lights. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Tigercat | 620E | 2016 |
$78,500
|
|
2018 CAT 559D Log Loader2018 CAT 559D Log Loader - CAB, A/C, CTR 426 delimber, mounted on Pitts Trailer. HYD Landing Gear, Meter reads - 8,347 hours. |
CAT | 559D | 2018 |
$104,900
|
|
Tigercat 234B Loader w/CSI 264 Delimber & CSI Buck Saw2018 Tigercat 234B Loader with CSI 264 Delimber and CSI DL-4400 Bucksaw. Hour meter reads 4,395 hours. Loader is tight, 32' boom. CSI DL-4400 bucksaw has less than 300 hours on it, 264 delimber is in good working order. Trailer is in good condition, tires estimated at 30%. Heat, A/C, radio, & lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Tigercat | 234B | 2018 |
$203,500
|
|
Tigercat 615C Skidder2014 Tigercat 615C Bogie Skidder. Hour meter reads 10,454 hours. 30.5x32 front tires & 750/55-26.5 bogie tires estimated at 40%, includes a set of tracks. Turnaround seat, Webasto preheat system, & winch. Heat, A/C, radio, lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
Tigercat | 615C | 2014 |
$155,000
|
|
Ponsse Buffalo Forwarder2012 Ponsse Buffalo Forwarder. Hour meter reads 16,000 hours. Mercedes tier 3 engine. 710/45-26.5 tires are estimated at 25%, will need a few new rear tires. Main boom was recently replaced, K100+ crane with tilting crane base, Grippen 35HD grapple is in good condition. New joysticks. 3600mm rear frame, rear tether hitch, & blade. Heat, A/C, radio, lights, & rearview camera. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northwest USA. |
Ponsse | Buffalo | 2012 |
$162,500
|
|
CTR 426 DelimberCTR 426 Delimber. In good working order. One knife needs to be replaced. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. |
CTR | 426 | Unknown |
$3,000
|