Sort By:   GridGallery
Photo Title
Make Model Year Price
Ponsse Elk 6 Wheel Forwarder

Ponsse Elk 6 Wheel Forwarder

2009 Ponsse Elk 6 Wheel Double Bunk Forwarder. This machine has around 12,000 hours, Mercedes Benz engine, runs and starts good, turbo has been replaced, strong hydraulics and cylinders, transmission is in good working order, T90 crane, tight center section, 600 tires, bogies are in good working condition, pre heater. Heat, A/C, lights and radio. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Ponsse Elk 2009
$154,500
Timberjack 610 Double Bunk Forwarder

Timberjack 610 Double Bunk Forwarder

1997 Timberjack 610 Double Bunk Forwarder. This machine has a Cummins, 4BT engine, runs and starts good, 11,000 hours, rebuilt transmission and transfer case, clutch was redone, boom was recently gone through, new rotator head - Pro Link snubber, strong hydraulics - 2 new pumps, new brakes, 2 new 28Lx26 tires, A set of Bear Claw chains 70-80%, spare rim, heat, A/C, and LED lights. Contact Aaron Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Timberjack 610 1997
$56,500
Harricana 50' Stroke Delimber

Harricana 50' Stroke Delimber

Harricana 50' Stroke Delimber. This delimber has new knives, new chain, new 5 cylinder hydraulic motor, new sprocket, straight boom with no welds. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Harricana 50' 2019
$7,500
Drott Case 40 Cruz-Air Log Loader ***SOLD***

Drott Case 40 Cruz-Air Log Loader ***SOLD***

1986 Drott Case 40 Cruz-Air Log Loader. This equipment has a Detroit Diesel 453 engine recently rebuilt, runs and starts good, Bi-directional steering, four wheel drive. Manual extendable boom, 8' L stick, log grapple, strong hydraulics, new cylinders, 4 outriggers, auxiliary hydraulic valve, 17.5-25 tires. Electrical has been gone through. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD***

Drott 40 1986
$14,500
John Deere 648GIII Skidder ***SOLD***

John Deere 648GIII Skidder ***SOLD***

2003 John Deere 648GIII Dual Arch Grapple Skidder. This skidder runs and starts good has been well maintained, Sweda axles, rear axle was rebuilt. Direct Drive, tight center section, strong hydraulics and cylinders, engine is currently being rebuilt. New 30.5x 32 tires with dual rims, heat, A/C, and LED lights. Duals are available for additional cost. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD***

John Deere 648GIII Unknown
$61,500
Hood S182 Self Propelled Loader

Hood S182 Self Propelled Loader

1995-96 Hood S182 Self Propelled Loader. This equipment has a John Deere 6068T engine, runs and starts good, 7,094 hours, strong hydraulics and cylinders, drive system is in good working order, air brakes, tight boom and grapple, Hood 360 continuous grapple, lever controls, solid carrier, heat, and lights. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Hood S182 1995
$33,500
Turbo Forest TF42 Cable Skidder

Turbo Forest TF42 Cable Skidder

1994-95 Turbo Forest TF42 Cable Skidder. This skidder has a Perkins engine, runs and starts good, strong hydraulics and cylinders, hydrostatic transmission, 2 winch machine. Only one winch working at this time, few leaks nothing major. Tires are @ 50% with chains. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA.

Turbo Forest TF42 1994
$19,500
John Deere 759G Feller Buncher ***SOLD***

John Deere 759G Feller Buncher ***SOLD***

2005 John Deere 759G Feller Buncher. Hour meter reads 7,370 hours, runs and starts good, strong hydraulic and pumps. Pump was gone through at 4,000 hours, new final drive, bearings were changed every 1,500 hours on final drives, 250 hour oil change, leveling system is in good order. Complete undercarriage @ 300 hours ago, 24" pads. 22" head 40 degree tilt, straight blade, good teeth and grab arms. Heat, A/C, and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. ***SOLD***

John Deere 759G 2005
$119,500
Morbark 2455 Total Flail Chiparvestor Combo Machine

Morbark 2455 Total Flail Chiparvestor Combo Machine

1995 Morbark 2455 Total Flail Chiparvestor Combo Machine. This machine has a 3412 CAT 800 HP engine and a 3306 325 HP CAT engine, they both run and start good. Both have been updated. 27" capacity, updated key knife system, updated to an auger and bark pusher. Strong hydraulics and pumps, well maintained, Debarker is in good working order - just replaced flail, strong hydraulics and cylinders, Morlift 500 loader with cab, heat, A/C, and lights. Tri axle carrier has good brakes and tires. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Morbark 2455 1995
$125,000
Hood 20000 6x6 Self Propelled Loader with Slasher

Hood 20000 6x6 Self Propelled Loader with Slasher

1998 Hood 20000 6x6 Self Propelled Loader with Slasher. This equipment has a 6068 John Deere engine, runs and starts good, strong hydraulics, tight boom and continuous grapple, live heel, 13,000 hours. 60" Hood saw. Folding/sliding butt board, carrier is in good order but does need brakes, heat, A/C, block heater, and quick couplers. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA.

Hood 20000 1998
$29,500
Peterson 4800E Flail Debarker

Peterson 4800E Flail Debarker

2008 Peterson 4800E Flail Debarker. This equipment has a CAT C-9 engine, runs and starts good. Hours are estimated @ 8,200 hours, recently full serviced, all filters, bark pusher, slides, batteries, repacked cylinders and lifts. Flails are in good working order, 23" diameter opening, remote control. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Peterson Pacific 4800E 2008
$109,500
Link-Belt 2800 with a Denharco DT3500 Delimber

Link-Belt 2800 with a Denharco DT3500 Delimber

1997 Link-Belt 2800 with 1998 Denharco DT3500 Delimber. This equipment runs and starts good, around 11,500 hours, strong hydraulics, cylinders and hoses are in order, straight boom and inner boom, knives are in good working condition, butt plate, undercarriage is @ 30%, heat. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Link Belt 2800 1997
$64,900