Sort By:   GridGallery
Photo Title
Make Model Year Price
Bandit Model 2590 Whole Tree Chipper  ***SOLD***

Bandit Model 2590 Whole Tree Chipper ***SOLD***

2013 Bandit Model 2590 Whole Tree Chipper. This chipper has a CAT C-15 585 HP turbo diesel engine with only 5,900 hours. Wireless remote Control, tandem axle, air brakes. Auto-feed reverse, hydraulic flow regulator, in-feed chain and knives are all in good working order, over the top discharge, pro Heat. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. ***SOLD***

Bandit Model 2590 2013
$115,000
John Deere 748GIII Skidder ***SOLD***

John Deere 748GIII Skidder ***SOLD***

2005 John Deere 748GIII Dual Arch Grapple Skidder. This skidder has a Torque transmission, 2 new 30.5 x 32 tires, the other 2 are @ 40% with Diamond chains. Dual Arch. tight pins and bushings, strong hydraulics and cylinders, engine runs and starts good. Heat, A/C, and lights. Maintained on regular service schedule. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. ***SOLD***

John Deere 748GIII 2005
$57,500
Valmet 860.1 6 Wheel Forwarder

Valmet 860.1 6 Wheel Forwarder

2006 Valmet 860.1 6 Wheel Forwarder. This machine has a Sisu engine, runs and starts good, 15,850 hours, strong hydraulics, new hydraulic pump, tight center section, axles and bogies are all in good working order, new bogie bearings and seals, tight boom and grapple. Heat, A/C, and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Valmet 860.1 2006
$92,500
TimberPro TL-725B Harvester with a Rolly II Head ***SOLD***

TimberPro TL-725B Harvester with a Rolly II Head ***SOLD***

2011 TimberPro TL-725B Harvester with a Rolly II Head. Hour meter reads 9,700 hours, Cummins 8.3 engine, runs and starts good, new pan gasket and main seal, flex plate was done at the same time, valve banks were gone through and resealed. Espar pre heat system, fire suppression system. Strong hydraulics, and cylinders, drive pumps are in good working order, 2 new final drives. Undercarriage is @ 50%, 28" double grouser pads. Newer house bearing 1,500 hours ago. Rolly II head, grab arms and both bottom and topping saw are in good working condition. Dasa 4 computer, good glass, heat, A/C, and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD***

Timberpro TL-725B 2011
$149,900
Vermeer BC1400 Chipper ***SOLD***

Vermeer BC1400 Chipper ***SOLD***

2006 Vermeer BC1400 Chipper. This equipment has a 14” capacity. This self-feeding drum style chipper is Powered by a Caterpillar turbo diesel engine, runs and starts good, 1,347 hours, been cleaned, serviced, fully tested, knives in good order with extras. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD***

Vermeer BC1400 2006
$16,500
Timberjack 1210 Forwarder ***SOLD***

Timberjack 1210 Forwarder ***SOLD***

1995-1996 Timberjack 1210 8 Wheel Double Bunk Forwarder. This equipment has a Perkins engine, runs and starts good, strong hydraulics and cylinders few minor leaks, decent center section has a little play, bogies are in good working order. Comes with one set of tracks and spare tire, new Lexon glass. Shift button on control will need some attention but works. Heat, A/C need charging, and lights. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***SOLD***

Timberjack 1210 1996
$38,900
Timbco 425EXT Harvester with a 2015 Rolly II Head

Timbco 425EXT Harvester with a 2015 Rolly II Head

2005 Timbco 425EXT Harvester with a 2015 Rolly II Head. This equipment has 8,100 hours, Cummins QSC 8.3L, runs and starts good, Espar pre heat system, strong hydraulics and drive motors, newer undercarriage, 24" double grouser pads. Tight boom, swing gear is in good working order. 2015 Rolly II Processing head with 1,250 hours, upgraded to a Woodland Eaton Computer system with books. Heat, A/C, and LED lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

Timbco 425EXT 2005
$200,000
Ponsse Bison Forwarder

Ponsse Bison Forwarder

2001 Ponsse Bison 6 Wheel Double Bunk Forwarder. This equipment has a newer Mercedes Benz 4 cylinder engine with approximately 6,000-7,000 hours, runs and starts good. 13,000 total machine hours. New center pins and big bearing. New rear brake, new controller, strong hydraulics and cylinders. Tight boom and grapple. Heat, A/C, and lights. Tires are in good working order with a set of tracks. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Ponsse Bison 2001
$87,500
Tigercat 620E Skidder

Tigercat 620E Skidder

2014 Tigercat 620E Skidder. This equipment has 35.5 x 32 rubber. Heavy Duty outboard planetary axles. For more information contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Tigercat 620E 2014
$Call for Price
Timbco 415C Harvester with a Ponsse H73 Head

Timbco 415C Harvester with a Ponsse H73 Head

1998 Timbco 415C Harvester with a Ponsse H73 Head. This equipment has a John Deere 6068T engine, runs and starts good, strong hydraulics and cylinders. Undercarraige is in good working order, single grouser pads. Ponsse H73 head is solid, grab arms and feed rollers are all in good working order, measuring system works as it should, Ponsse 1000 computer. Heat, A/C, and lights. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

Timbco 415C 1998
$52,500
Ponsse Ergo Harvester with H7 Head

Ponsse Ergo Harvester with H7 Head

2005 Ponsse Ergo Harvester with H7 Head. This machine has many new parts. Mercedes Benz engine, runs and starts good, strong hydraulics and cylinder. Recently new crane pump. Crane has been repined and bushings top to bottom. New center pins. New injectors and head gasket. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Ponsse Ergo 2005
$99,900
Ponsse Buffalo King Double Bunk Forwarder

Ponsse Buffalo King Double Bunk Forwarder

2013 Ponsse Buffalo King Double Bunk Forwarder. This machine was just gone through by Ponsse. Has a Mercedes 6 cyl. engine, runs and starts good, bunk extenders. New Wabasto engine pre-heater, fire suppression package, strong hydraulics, cylinder, pins and bushings were gone though. Tight Center bearing. Tight K100 crane and newer over-sized grapple. Bogies were gone through. Light package, premium seat with heat and A/C. Tires are in good working order. New Wiring harness. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Ponsse Buffalo King 2013
$185,900