Sort By:   GridGallery
Photo Title
Make Model Year Price
Prentice 210E Loader with a CSI 4400 Delimber

Prentice 210E Loader with a CSI 4400 Delimber

1999 Prentice 210E Loader with a CSI 4400 Delimber. This equipment has a John Deere engine, runs and starts good, strong hydraulics and cylinders few minor leaks, tight joystick controls, tight boom and grapple, rotator and swing motor are in good order, Delimber is in good working order, good brakes, will need a few tires, heat, A/C needs work. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located Southeast USA.

Prentice 210E 1999
$28,500
Timberjack 460D Skidder

Timberjack 460D Skidder

2004 Timberjack 460D Single Arch Grapple Skidder with Winch. Hour meter reads 5,600 hours, engine has 1,100 hours, runs and starts good, strong hydraulics and hydrostatics, cylinders are in good order, one grapple cylinder has a leak - not bad, winch is in good working order - 7/8 cable, 30.5x321 tires, tires are @ front 25%, rear tires @ 60%, heat, A/C needs a hose and charge, center has a little play not bad, arch pins are good. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located Southeast USA.

Timberjack 460D 2004
$34,900
2003 Fabtek 344B Forwarder

2003 Fabtek 344B Forwarder

FABTEK 344B SINGLE BUNK FORWARDER 4 CYL JOHN DEERE POWERSHIFT JOYSTICK CONTROLS EXTENDABOOM 28L-26 RUBBER

Fabtek 344B 2003
$Call for Price
2005 Fabtek 153 Harvester

2005 Fabtek 153 Harvester

FABTEK 153 TRACKED HARVESTER 6 CYL JOHN DEERE RECANT OVERHAUL ON ENGINE 3000 HOURS ON UNDERCARRAIGE FABTEK FOUR ROLLER HEAD

John Deere 153 2005
$99,000
CTR 550 Pull Through Delimber with Buck Saw

CTR 550 Pull Through Delimber with Buck Saw

2000 CTR 550 Pull Through Delimber with Buck Saw. This equipment has low hours, saw and delimber are in good working condition, strong hydraulics. Contact Erik @ Red Pine Equipment 218-720-0933. Delimber is located in Northeast USA.

CTR 550 2000
$8,000
2005 Fabtek 546C Forwarder

2005 Fabtek 546C Forwarder

2005 Fabtek 546C, complete re-built engine, new rear-end, new jib cly., new rotate motor on bucket, 700 rear rubber, 30.5x32 front

Fabtek 546C 2005
$129,000
2000 Fabtek 548C Forwarder/Skidder

2000 Fabtek 548C Forwarder/Skidder

Owner operated machine. 13,950 hours. Heat & A/C. Pro Heat. Good rubber all around, 700/50-26.5 rubber. Excellent running 6068T Deere engine. No oil leaks or blow by. Transmission shifts excellent. Clean inside and out. Tracks to go with it. IQAN diagnostic display. Squirt boom. Serial#64802829513.

Fabtek 548C 2000
$120,000
Tigercat 1065 Forwarder

Tigercat 1065 Forwarder

1995 TigerCat 1065 Forwarder with Tracks

Tigercat 1065 1995
$Call for Price
CAT 501HD Processor ***SOLD***

CAT 501HD Processor ***SOLD***

2008 CAT 501HD Processor with a Dangle Processor Head. This machine has 9,800 hours, runs and starts good, strong hydraulics, undercarriage is in good working order - 65-75%, tight boom, has been re-enforced, computer in good working condition, PH head in good working condition was completely rebuilt 8 months ago, new grab arms, feed rollers, new saw motor, heat, A/C, and radio. Machine has been well maintained. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA. ***SOLD***

CAT 501HD 2008
$114,900
Morbark 2755 Flail Chipper  ***SOLD***

Morbark 2755 Flail Chipper ***SOLD***

2011 Morbark 2755 Flail Chipper. This machine has 10,500 hours, CAT C27 tier II 875 HP main engine, twin disc hydraulics manual clutch, CAT 440 HP tier III C13 flail drive engine with triple gear box 1: 1 reduction gear box, they run and starts good, 27"x 55" infeed opening, feed roller is in good order. Discharge system consisting 60-1/2" wide x23' long telescoping drag chain conveyor drive, 7/8 chips, hydraulic tilt down cab for transport, Mor-lift 500 knuckleboom loader, joystick control, Rotobec 442 grapple, 3 knife disc, heat, A/C, and emergency shut down system. Re-worked flail pumps and rebuilt gear box for flail pumps 11/16. New bottom flail 11/16. New face plate and pocket holders on disk, injectors re-sealed. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located Southcentral USA. ***SOLD***

Morbark 2755 2011
$349,000
John Deere 548GIII Grapple Skidder

John Deere 548GIII Grapple Skidder

2004 John Deere 548GIII Grapple Skidder. This machine has 13,000 hours, runs and starts good, strong hydraulics and cylinders, tight pins and bushings, transmission is in good working order, 28Lx26 tires, heat, A/C, and lights. Well maintained. Winch and extra drive shaft included. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA.

John Deere 548GIII 2004
$65,900
Clark Ranger F67 Skidder ***SOLD***

Clark Ranger F67 Skidder ***SOLD***

1989 Clark Ranger F67 Skidder - Cummins 5.9, 30.5 X 32 tires, overall excellent condition, one of the nicest Rangers we've ever seen. No winch on the machine currently but we can provide a winch with drive shaft and controls for approximately $4,500. Price on skidder is $27,900. Located in Minnesota USA. We are able to disassemble and put this machine into a container for overseas shipment. Contact Kelly @ 218-720-0933. ***SOLD***

Clark Ranger F67 1989
$27,900