Featured in Sawmill Equipment

Sort By:   GridGallery
Photo Title
Make Model Year Price
Circular sawmill with wheel loader

Circular sawmill with wheel loader

Stationary circular sawmill for sale. 50” inserted tooth blade, Detroit 6-71 power with rebuilt clutch, rebuilt blower, new injectors and fuel lines. Stack of three hydraulic pumps. Custom adjusters for headsaw belt tension as well as hydraulic pump belt. 20’ custom built tip table conveyor to sort slabs/lumber. 20’ green chain. 12’ carriage with hydraulic forward/recede and dogs. New carriage drive motor with 1 year on it. Manual log deck/log turner. Wheel loader is a 1979 JD444. Clean, strong engine. Few minor hydraulic leaks. Has pin on forks and a 4 way bucket. Forward remotes for bucket or other attachment.

- - Unknown
$31,000
WoodMaster 725 Planer

WoodMaster 725 Planer

WoodMaster 725 Planer. This planer has under 25 hours of use on it. Comes with 64 brand new knives of different formats. Has feed reverse switch & adjustable feed speed switch. Includes spiral head that has 164 separate 4 sided cutting knives on the head, a 725 Pro-Pak, and the 725 3 side molding system that uses 2 - 3.5 HP Milwaukee routers to enable operator to mold 3 sides of stock wood in 1 pass. Specs can be viewed on the WoodMaster website for planer and 725 Pro-Pak with 3 side molding system. Also includes a 5 HP Big Max dust collection system with 2 - 55 gallon barrels for collection of dust and shavings. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Southwest USA.

Wood Master 725 Unknown
$15,900
TimberKing 2000 Sawmill

TimberKing 2000 Sawmill

2013 TimberKing 2000 Sawmill with Full Hydraulic Operation. This equipment has a 49 HP Kubota Diesel engine, approximately 160 hours on the meter, comes with close to 100 blades (about 30 blades are used but can be re-sharpened), also comes with blade sharpener and a blade tooth setter (both are brand new). This machine, once dialed in and set up properly, is very accurate to within 1/16". Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Southwest USA.

Timberking 2000 2013
$37,900
Kent Single Head Band Resaw System

Kent Single Head Band Resaw System

Kent Single Head Band Resaw System with Conveyor and Belt Feed Table. This equipment has a Leeson 30 HP electric motor. Tables and parts for a Woodmizer run around. Aftermarket blade guide system. AKA Blockhead Resaw. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Kent - Unknown
$Call for Price
5 Head Ultra Planer System

5 Head Ultra Planer System

2011 5 Head Ultra Planer System. This equipment has a 15 HP top motor (new bearings in top head in 2019) 10 HP on other motors. Air powered automatic feed. Air powered hold downs with aftermarket Z Drive automatic feeder. Can be sold with or without dust collection system. Dust collector does 6000 cubic feet per minute and is powered by a 15 HP 3 phase motor. Extra heads and lots of extra knives included. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

- Ultra 2011
$39,500
Sprout Waldron Pellet Mill

Sprout Waldron Pellet Mill

Sprout Waldron Pellet Mill. This is a turnkey Pellet Making Operation. The grinder system includes a bin for loading shavings to feed the hammer mill. The hammer mill, feed conveyor, and auger in the feed bin are controlled with sensing units so that the mill cannot be over fed and jam up. As the amps on the hammer mill climb the feed auger slows, when the amps reach a pre-set limit the feed conveyor stops to allow the hammer mill to catch up. This is all 3 phase 240v components. The hammer mill has a ¼” screen, which is the correct size for the pellet system. It has a 40 HP motor. There is a small 220v blower which takes the feed stock out of the chamber, the hammer mill fills and feeds it into the hopper above the pellet mill. There is a 30’ out feed conveyor that the pellets fall onto out of the pellet mill, which also has a variable speed control and is reversible. There are misc. spare parts included. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Sprout Waldron - Unknown
$79,500
54" Sawmill ***SOLD***

54" Sawmill ***SOLD***

54" Sawmill with new teeth and holders. Setup great for 8's and 16's, new treated wood on track, 300 cummins big cam power unit on a portable trailer, hydraulic setworks and carriage, greasable bearings on saw. Ready to mill, currently setup if you'd like to see it run. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. ***SOLD***

- 54 Unknown
$11,900
JCB 506CHL Telescopic Forklift

JCB 506CHL Telescopic Forklift

2007 JCB 506CHL Telescopic Forklift. This machine has 4 wheel drive and steer, JCB diesel engine, runs and starts good, ROPS, 6,000 LBS. Lift Capacity, 42' Reach, 66" frame. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

JCB 506CHL 2007
$Call for Price
Morbark PS-8 Post Peeler

Morbark PS-8 Post Peeler

Morbark PS -8 Post Peeler. This machine is a complete mill from one end to other, includes in-feed log deck, in-feed conveyor, peeler, out-feed conveyor with kicker. 30” circle saw, cut up deck with air pop ups for 5 length and log kickers, log deck elevator out-feed, 8 pole bins, bark blower, air compressor, all electric switches and hydraulic valves included. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

Morbark PS-8 -
$37,500
Sanborn Scragg Mill

Sanborn Scragg Mill

1990 Sanborn Scragg Mill. This equipment has 52" saws, opens 24", 6'-16' lenghts, overhead carriage 30'. 4 strand log deck, drop belts, 2 -125 HP motors, all electrics come with starter and switch box slab & sawdust box conveyor, Silvatech setworks. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Southwest USA.

Sanborn Scragg 1990
$84,000
Posch 500 Post Peeling System

Posch 500 Post Peeling System

Posch 500 Post Peeling System. This equipment includes a log deck with stop and loader, infeed conveyor, PTO driven. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA.

Posch 500 -
$13,900
Salsco 60" Shavings Mill ***SOLD***

Salsco 60" Shavings Mill ***SOLD***

2009 Salsco 60" Shavings Mill. This equipment only has 390 hours, CAT 200 HP engine, runs and starts good. Includes the shavings mill, 9' log length, 60" wide trough, 15' and 20' conveyor, de-sizer and a 30' conveyor. Full Operation. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA. ***SOLD***

Salsco 60 2009
$82,500