Featured in Harvesters/Processors

Sort By:   GridGallery
Photo Title
Make Model Year Price
2008 John Deere 1270D Harvester

2008 John Deere 1270D Harvester

2008 JOHN DEERE 1270D WHEELED HARVESTER 6 CYL DEERE HYDRASTATIC DRIVE 480C HEAD 600 RUBBER

John Deere 1270D 2008
$189,000
2008 CAT 501HD

2008 CAT 501HD

2008 CAT 501HD TRACKED HARVESTER 6 CYL CAT REBUILT ENGINE BY MICHIGAN CAT WITH WARRANTY FOUR ROLLER HEAD

CAT 501HD 2008
$189,000
Ponsse Ergo with H7 Harvesting Head ***SOLD***

Ponsse Ergo with H7 Harvesting Head ***SOLD***

2008 Ponsse Ergo with H7 Harvesting Head. This machine went through Ponsse's rebuild program about 4,000 hours ago. Reman Mercedes engine, front differential, & transmission. New wire harnesses. Newer hydraulic pump installed 1,800 hours ago. 700 tires are estimated at 50%, one set of tracks that are included are estimated at 70%. H7 processing head is in good working order. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. ***SOLD***

Ponsse Ergo 2008
$162,500
CAT 501HD Processor

CAT 501HD Processor

2008 CAT 501HD Processor with Fixed Head. This machine has 12,000 hours, runs and starts good, like new undercarriage, strong hydraulics. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northeast USA. ***REDUCED FROM $164,500.00***

CAT 501HD 2008
$149,000
John Deere 1270D Harvester

John Deere 1270D Harvester

2008 John Deere 1270D Harvester. 11,000 hours. Recent new injectors in engine which runs and starts good. H480 head has been rebuilt. 2 outer drive motors and one inner motor were rebuilt recently. Espar engine, hydraulic, and cab preheat system, strong hydraulics and cylinders, reman work pump and drive pump in the last 500 hours, tight boom and center section, stick and lift cylinders redone, bogies are in good working order, solid rear ends, 700 tires @ 50% with rear tracks, one set of chains. Feed rollers and grab arms are in good condition, Timbermatic HHM 300 computer. Heat, A/C,and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

John Deere 1270D 2008
$144,900
Ponsse Ergo Harvester with H7 Head

Ponsse Ergo Harvester with H7 Head

2008 Ponsse Ergo Harvester with H7 Head. This equipment has a Mercedes engine, runs and starts good, strong hydraulics and cylinders, new conical pins in the crane base and upper and lower in the pillar. 6/20/18 all new pressure hoses, case drain hose and steal lines inside the boom. All new inner and outer swing gear bolts. bogies are in good order. Computer was just cleaned out at Ponsse. 710 tires are good with 1 set of tracks. Heat, A/C, and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Ponsse Ergo 2008
$115,000
CAT 501HD Harvester with Fabtek 4 Roller Head

CAT 501HD Harvester with Fabtek 4 Roller Head

2008 CAT 501HD Harvester with Fabtek 4 Roller Head. Hour meter reads ~14,000 hours. CAT C6.6 engine starts and runs good. 24" single grouser pads. Undercarriage is estimated at 65%. Newer motor and pump with 600 hours. New ICAN computer. New chains on the feed wheel, also has new knives. Preheater. Enclosed cab has heat, A/C, & lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

CAT 501HD 2008
$105,000
Rottne H14 with 561 SP Processing Head

Rottne H14 with 561 SP Processing Head

2008 Rottne H14 Processor with 561 SP Processing Head. Hour meter reads 12,000 hours. John Deere 6068 engine starts and runs good. 600/45-26.5 tires are at 85%. RK 140 boom is tight. Self leveling cab works as it should. New pins and bushings, the brake on the head, knife pins & bushing, and repacked cylinder. Cab bushing has recently been changed. Enclosed cab has heat, A/C, and radio. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA.

Rottne H14 2008
$105,000
CAT 501 Processor with Fabtek 4 Roller Head ***SOLD***

CAT 501 Processor with Fabtek 4 Roller Head ***SOLD***

2008 CAT 501 with Fabtek 4 Roller Head. Hour meter reads ~20,000 hours. Has had a reman CAT engine installed. 24" triple grouser pads, undercarriage is in good working order. Fabtek 4 roller head has a reman frame, and one feed roller has just been rebuilt. Heat, A/C, and radio in cab. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northeast USA. ***SOLD***

CAT 501 2008
$87,500
Valmet 425EXL Harvester with Quadco 5660 Head ***SOLD***

Valmet 425EXL Harvester with Quadco 5660 Head ***SOLD***

2008 Valmet 425EXL Harvester with Quadco 5660 Head. Hour meter reads 9,310 hours, newer Cummins 8.3L engine has 1,609 hours. New main auxilliary pump was installed summer of 2022. 24" single grouser pads, undercarriage is estimated at 80%, some rollers will need to be replaced. Quadco 5660 intermittent harvesting head, feed wheels and motors are in good working order. Newer main saw, rollers, bearings, gears, and ring gear. Espar preheat system, heat, A/C, & leveling cab. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Southcentral USA. ***SOLD***

Valmet 425EXL 2008
$Call for Price