Featured in Logging Equipment

Sort By:   GridGallery
Photo Title
Make Model Year Price
Valmet 644 Forwarder ***SOLD***

Valmet 644 Forwarder ***SOLD***

1998 Valmet 644 Single Bunk Forwarder. This machine has a strong Cummins 4BT engine, runs and starts good, quick couplers for cold start. Strong hydraulics and recently went through and resealed valve bank. Loader is tight and has extenda boom that is in good working condition. Center section is in good condition, recently repacked cylinders on loader, brakes all work. Lever controls. 23.1x26 tires are at approx. 50%. New Lexan in cab, Heat and lights. AC is there but needs some work. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. ***SOLD***

Valmet 644 1998
$35,900
Lemco 72" Saw Table

Lemco 72" Saw Table

1998 72" Lemco Saw Table in good working condition. Will need a couple of hoses changed. Used sparingly for tree length and in good condition for age. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Lemco 72" 1998
$14,500
1998 Rottne EGS

1998 Rottne EGS

good running machine ready to work with recent service on Fluids and filters. currently has 12029 original machine hours Equipped with Nokia 700/70/34 at 60% with ice chains on front, rear tires Trelleborg 700/50/26.5 at 60% tread. Harvester comes with two sets of boggy tracks, the current mounted set of Pedno winter/rock tracks at 60% and a set of Eco Combi tracks at 25%. This machine has the Iveco 6 cylinder engine and Rottne updated high flow hydraulic pump and proportional control. all three pulse transmitters replaced in the head, along with memory card in main computer. This machine uses the Rottne system 90 CTL system and has the Rottne EGS head with 25" bar, 18x chain .404" auto tension. Swing cylinders and stick cylinder repacked in summer 2020. Machine would come with 2 new bars, some good chains, Parts manual and System 90 operating manual, and misc Rottne spare parts I purchased this machine to cut a large pine job 2 1/2 years ago and i primarily log with cable skidders and select cutting in Western NY. No longer need the machine and would consider possble trade for 6cyl cable skidder.

Rottne SMV Rapid EGS 1998
$30,000
Barko 160D Loader

Barko 160D Loader

1998 barko 160D with 60" siiro saw table. 1owner 7475 actual hours, John Deere 6 cyl. 30ft. boom rotobec 360 1/2 cord bucket, heat air fan lever controls quick couplers. Mounted on 1986 gmc with 427 rebuilt less than 2000 miles on it. Greased daily well maintained, does not burn any oil. 1 extra saw blade few hoses few filters and extra fittings. RETIRED

Barko 160D 1998
$45,000
Timberjack 608B Feller Buncher

Timberjack 608B Feller Buncher

1998 Timberjack 608B Feller Buncher with a 22" Koehring Sawhead. This machine has a Cummins 5.9 engine, starts and runs good. Strong hydraulics, brand new main pump, implement, and pilot pump. 1 New Drive motor. Tight boom and Sawhead. 24" double grouser pads. Heat and lights work, A/C needs a fitting on the compressor. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Timberjack 608B 1998
$52,500
Eco Log 550B Processor with a Logmax 5000 Head

Eco Log 550B Processor with a Logmax 5000 Head

1998 Eco Log 550B Processor with a Logmax 5000 Head. This processor has many new parts on the Logmax head, new main pump in 2013, rebuilt pump drive assembly this spring, both drive pumps have been gone through, all fluids changed this spring, four chains, tires are @ 70%, new crank bearings this spring and new piston rings, 15,000 hours. Machine is only used for 6 months of the year for the past three years, seasonal operation. Comes with spare hoses, filters, and any other misc. parts associated with it, also has brand new parts for the head. A/C does not work, heater does, has a 24 volt system. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Eco Log 550B 1998
$29,900
Timberjack 1010B Forwarder

Timberjack 1010B Forwarder

1998 Timberjack 1010B 6 Wheel Double Bunk Forwarder. This machine has a Cummins 4BT engine, runs and starts good, strong hydraulics and drive system. New center oscillating bearing. Bogies are in good order, brakes are not working, squirt boom and grapple are in good working order, 710 tires with tracks, 28 front with chains. Heat, A/C, and lights. Contact Erik @ Red Pine Equipment 218-720-0933. Forwarder is located in Northeast USA.

Timberjack 1010B 1998
$47,500
Lemco 7200 Slasher 72" Saw Table

Lemco 7200 Slasher 72" Saw Table

1998 Lemco 7200 Slasher 72" Saw Table. This equipment has a straight blade, teeth are in good order, hydraulic butt board, strong saw motor. Nice condition. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

Lemco 7200 1998
$18,500
Link Belt 2800 Quantum with ProPac 453 Delimber

Link Belt 2800 Quantum with ProPac 453 Delimber

1998 Link Belt 2800 Quantum with ProPac 453 Delimber. This equipment has an Isuzu 6 cyl. engine, starts & runs good, strong pumps and drive motor, straight boom and good cables. Undercarriage is in good working order. Hour meter reads 13,500 Hours. New windows & seat. Fresh oil and all filters. Runs perfect. Circle topping saw - just had the saw hammered, new teeth. Heat & A/C. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

Link Belt 2800 1998
$Call for Price
CASE 903B with ProPac 453 Delimber

CASE 903B with ProPac 453 Delimber

1998 Case 9030B with ProPac 453 Delimber. This equipment has a Cummins engine, runs and starts good, Wabasto pre-heater, pumps have been redone, strong hydraulics and cylinders, lift cylinders have just been repacked, new bearings on the rollers, straight boom knives in good working order, new grab arms, newer injection pump. Heat and lights. A/C may need a charge. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA.

CASE 903B 1998
$55,900
John Deere 540GII Cable Skidder ***SOLD***

John Deere 540GII Cable Skidder ***SOLD***

1998 John Deere 540GII Cable Skidder. This machine has a rebuilt engine and transmission by Nortax equipment. New drive shaft, new rollers with bushings, new pins and bushings in steering cylinder, strong winch, enclosed cab with heat, lights work. Needs a new seat pad and new glass. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. ***SOLD***

John Deere 540GII 1998
$39,500
John Deere 748GII Skidder

John Deere 748GII Skidder

1998-99 John Deere 748GII Dual Arch Grapple Skidder. This equipment has a Cummins 8.3 engine, runs and starts good, Power Shift transmission in good working condition, tight center, little play in arch pins, strong hydraulics and cylinders with few minor leaks, 35.5 tires @ 50% with dual rims. Trail blade with tilt. Heat and lights. Contact Aaron @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA.

John Deere 748GII 1998
$39,500