Photo |
Title
|
Make | Model | Year | Price |
1998 Hyundai 200 Processor with Fabtek Dangle HeadGreat running machine ,Fabtek forestry package, High walker, forestry cab, 1 owner |
Hyundai | Hyundai 200 High Walker | 1998 |
$Call for Price
|
|
Hyundai 210LC-7 with Propac 453 Delimber ***SOLD***2007 Hyundai 210LC-7 with Propac 453 Delimber. Hour meter reads 8,680 hours. New engine with 750 hours. New Berco undercarriage, 28" triple grouser pads. Straight boom, delimber is in good condition. Newer oil pump, new chain on the boom, & new drive motor. New side rollers & new pins and bushings in grab arms. Heat, radio. Open to offers. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. ***SOLD*** |
Hyundai | 210LC-7 | 2007 |
$64,900
|
|
Hyundai Robex 210LC-7 with Propac 453 Delimber2005 Hyundai Robex 210LC-7 with Propac 453 Delimber. Hour meter reads 12,710 hours. Cummins 5.9 engine. This machine has a new boom as of 2019, some work has been done on the head, undercarriage is at about 60%. 28" triple grouser pads. Propac 453 Delimber works well. Straight, dry machine. Hours may increase because it's currently in use. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Hyundai | Robex 210LC-7 | 2005 |
$60,000
|
|
Hyundai Robex 210 LC-3 Yoder1997 Hyundai Robex 210 LC-3 Yoder. Hour meter reads 8,838 hours. 28" triple grouser pads, undercarriage is estimated at 75%. Dry valve bank. Tight boom & thumb bucket. Hydraulics are strong. Enclosed cab has heat & radio. Contact Aaron @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. |
Hyundai | Robex 210 LC-3 | 1997 |
$98,000
|
|
2001 HYUNDAI 1302001 HYUNDAI 130 TRACKED HARVESTER 4BT CUMMINS FOUR ROLLER HEAD |
Hyundai | 130 | 2001 |
$49,500
|
|
International with Rotobec Loader ***SOLD***1979 International with Rotobec Loader and Siiro Slasher. CAT 3802 engine starts was recently rebuilt. 15,000 miles, 1,200 hours since the overhaul. New input bearing, pump drive, & suction lines. Rotobec continuous grapple, dead heel, & lever controls. Siiro slasher saw motor has been rebuilt, includes an extra pump, new saw blade, two boxes of teeth, hydraulic cylinders, stroke slasher, and another complete saw ring. Also includes another tube, full chassis, bangboard, and extra knives. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. ***SOLD*** |
International | Siiro | 1979 |
$Call for Price
|
|
Iron Mule 5510 Forwarder1989 Iron Mule 5510 Forwarder. Hours are unknown, meter reads 1,747 hours. Ford 4cyl engine. 23.1x26 tires on the front are new, rears are estimated at 50%. Includes an extra tire without rim & chains. Minor leak on boom cylinder. Center and Gafner hydra-loader are tight. Can include extra tires for additional cost. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Iron Mule | 5510 | 1989 |
$22,000
|
|
Iron Mule Model 4500 Series Forwarder ***ON HOLD***Late 70’s Iron Mule Model 4500 Series Forwarder. 3 cylinder Ford engine runs and starts good. Manual stick with Hi/Low range. Newer injector pump, recently repacked cylinders, updated main boom and rack. Lexan in cab but no heat. 23.1 x 26 tires. Only 8’2” wide. Contact Erik @ Red Pine Equipment 218-720-0933. Machine is located in Northcentral USA. ***ON HOLD*** |
Iron Mule | 4500 | Unknown |
$17,500
|
|
1988 IRON MULE 55001988 IRON MULE 5500 4 CYL FORD STANDARD SHIFT LEVER CONTROLS 23.1-26 RUBBER NEW ON FRONT 90@ ON REAR |
Iron Mule | 5500 | 1988 |
$29,500
|
|
Iron Mule 220 ForwarderIron Mule 220 Single Bunk Forwarder. Hours are unknown. Ford engine starts and runs good. 18.4-26 tires are estimated at 35%, one has some weather checking but can be run as is. Brakes are good. Block heater has been installed. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
Iron Mule | 220 | Unknown |
$14,500
|
|
1987 IRON MULE 50001987 IRON MULE 5000 4 CYL FORD STANDARD TRANS LEVER CONTROLS ROTATOR BYPASS BUCKET 23.1-26 RUBBER |
Iron Mule | 5000 | 1987 |
$29,500
|
|
John Deere 540D Skidder1988 John Deere 540D Cable Skidder. 9,000 frame hours, 1,000 hours on engine. Rebuilt transmission. Cylinders were repacked, new center pins, radiator, water pump, hydraulic pump, shift linkage, & batteries. Winch recently reconditioned. New front drive shaft and U joints. Includes chains for the front. Contact Erik @ Red Pine Equipment 218-720-0933. Equipment is located in Northcentral USA. |
John Deere | 540D | 1988 |
$Call for Price
|